CHANNELS

Subscribe to the InfoTech eNewsletter

infoTECH News

TMCNet:  Fujitsu Semiconductor Successfully Embeds Flash Memory onto DDC Technology

[December 11, 2013]

Fujitsu Semiconductor Successfully Embeds Flash Memory onto DDC Technology

(ENP Newswire Via Acquire Media NewsEdge) ENP Newswire - 11 December 2013 Release date- 10122013 - Yokohama, Japan - Fujitsu Semiconductor Limited announced that it has developed the world's first technology to produce chips with embedded flash memory on logic circuits fabricated using deeply depleted channel (DDCTM) technology, with the 55nm process at the company's Mie Plant.

This makes it possible to consolidate DDC-for low-power operation in a conventional CMOS design-with flash memory, which is non-volatile memory, on a single chip, opening up new possibilities for a wide range of applications, such as the Internet of things. Details of this development will be presented at the IEEE International Electronic Device Meeting (IEDM) 2013, opening December 9 in Washington, DC.

As the Internet of things-in which many kinds of devices are connected to each other via the Internet-becomes more common, there is likely to be a growing demand for devices such as LSIs with built-in sensors for use in wireless sensor networks. For applications such as these, in addition to the necessary characteristics of low-voltage operation and low power consumption, there is demand for device equipped with non-volatile memory, which does not require power for storing sensor data.

Fujitsu Semiconductor licensed technology from SuVolta, Inc., and then worked on co-developing the world's first practical implementation of low-power DDC technology. Production of these chips has already begun at Fujitsu Semiconductor's Mie Plant. Fujitsu Semiconductor has developed a fabrication technology that makes it possible to consolidate DDC transistors on the same chip with floating-gate tunnel oxide (FLOTOX) flash memory.

In FLOTOX flash memory (Figure 1), inserting electrons into a floating gate (program), and extracting electrons from it (erase), are used to represent the 0s and 1s of data. When inserted electrons leak out of the floating gate, it becomes impossible to store data correctly. Indeed, the 'single bit charge loss' (SBCL) that can occur after repeated program/erase cycles is the greatest challenge when using this design. It had been thought that steps such as 'STI corner rounding' and 'tunnel oxide formation' used in FLOTOX fabrication need to be processed at high temperatures (approximately 1,000-degreeC) in order to avoid this failure.

DDC transistors (Figure 2), however, are characterized by the formation of the depleted layer, where dopants are held to very low density, underneath the gate electrode. The use of high-temperature processes is incompatible with the formation and retention of this kind of layer.

Fujitsu Semiconductor's development team focused on forming FLOTOX using only low-temperature processes. They conducted a complete review, paying close attention to each process along the way, and found that adjustments that would optimize the dopant density distribution in the channel region and source/drain electrodes would result in process conditions that can form FLOTOX structures, while maintaining the characteristics that DDC transistors require. Test chips produced with these new parameters were confirmed to have good initial characteristics for flash-memory operation and to be free from SBCL failures after repeated program/erase cycles, demonstrating that it is free from reliability problems.

Furthermore, in the course of this optimization work, it was found that the mechanism that produces SBCL is not current stress on the tunnel oxide film, as previously believed, but is dictated by hot hole injection near drains. This new understanding is likely to contribute to further process optimizations in the future.

Fujitsu Semiconductor looks forward to continuing to develop process technologies that strike an ideal balance between functionality, performance, and cost, and to contribute to higher added value in customer products.

Appendix IEEE International Electron Device Meeting (IEDM) 2013 Paper (1,111KB) Presentation (1,302KB) For more information: Fujitsu Semiconductor About Fujitsu Semiconductor Fujitsu Semiconductor Limited designs and manufactures semiconductors, providing highly reliable, optimal solutions and support to meet the varying needs of its customers. Products and services include Customized SoCs (ASICs), Foundry Service, ASSPs, and Ferroelectric RAMs (FRAMs), with wide-ranging expertise focusing on mobile, imaging, automotive and high performance applications. Fujitsu Semiconductor also drives power efficiency and environmental initiatives. Headquartered in Yokohama, it was established as a subsidiary of Fujitsu Limited on March 21, 2008. Through its global sales and development network, with sites in Japan and throughout Asia, Europe, and the Americas, Fujitsu Semiconductor offers semiconductor solutions to the global marketplace.

For more information, please see: : http://jp.fujitsu.com/fsl/en/ Company and product names mentioned herein are trademarks or registered trademarks of their respective companies. Information provided in this press release is accurate at time of publication and subject to change without advance notice.

Press Contacts Fujitsu Semiconductor Limited Public Relations [Editorial queries for this story should be sent to newswire@enpublishing.co.uk] ((Comments on this story may be sent to info@enpublishing.co.uk)) (c) 2013 Electronic News Publishing -

[ InfoTech Spotlight's Homepage ]


blog comments powered by Disqus

FOLLOW US

Subscribe to InfoTECH Spotlight eNews

InfoTECH Spotlight eNews delivers the latest news impacting technology in the IT industry each week. Sign up to receive FREE breaking news today!
FREE eNewsletter